2V0-41.20 Exam Questions Available For VCP-NV 2020 Certification

1. An NSX administrator noticed that the nsxclicommand times out after 600 secs of idle time.

Which CLI command disables the nsxcli time out value on NSX Manager?

2. An NSX administrator is configuring the KVM hypervisor host as a transport node and wants to apply the Failover Order as a NIC teaming policy.

Which profile allows the administrator to configure the NIC Teaming policy as Failover Order?

3. Which two choices are prerequisites to configure NSX-T on VDS? (Choose two.)

4. Which command is used to display the network configuration of the Tunnel Endpoint (TEP) IP on a bare metal transport node?

5. Which three steps are required to create an IPsec VPN tunnel? (Choose three.)

6. An NSX administrator wants to create a Tier-0 Gateway to support equal cost multi-path (ECMP) routing.

Which failover detection protocol must be used to meet this requirement?

7. What are two supported N-VDS modes? (Choose two.)

8. A user is assigned these two roles in NSX Manager:

– LB Admin

– Network Engineer

What privileges does this user have in the system?

9. An NSX administrator has configured a KVM hypervisor as a transport node.

Which kernel module on KVM implements a N-VDS?

10. Which CLI command should be executed on a KVM hypervisor to retrieve the VM interface UUID?

11. Which three functions require a Services Router (SR) component on an Edge node? (Choose three.)

12. What are two valid options when configuring the scope of a distributed firewall rule? (Choose two.)

13. A user is assigned these two roles in NSX Manager:

✑ LB Admin

✑ Network Engineer

What privileges does this user have in the system?

14. Which command is used to set the NSX Manager’s logging-level to debug mode for troubleshooting?

15. Refer to the exhibit.

Which NAT type must the NSX-T Data Center administrator create on the Tier-0 or Tier-1 Gateway to allow Web VM to initiate communication with public networks?

16. An NSX administrator would like to configure syslog for a KVM transport node.

Which host log files could be exported to a remote syslog server?

17. Which two ports are used by a transport node to communicate with the management and control planes in NSX-T Data Center 3.0? (Choose two.)

18. An NSX administrator is using ping to check connectivity between VM1 running on ESXi1 to VM2 running on ESXi2. The ping tests fails. The administrator knows the maximum transmission unit size on the physical switch is 1600.

Which command does the administrator use to check the VMware kernel ports for tunnel end point communication?

19. An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time.

Which CLI command disables the nsxcli time out value on NSX Manager?

20. Which is correct when deploying a NSX Edge in a KVM only environment?

21. How does Traceflow tool identify issues in a network?

22. What are the advantages of using a Tier-0 Gateway in ECMP mode? (Choose two.)

23. Which tool could be used to inspect the path of a packet in the data plane?

24. Where are Distributed Firewall logs containing access decisions stored?

25. An NSX Administrator has created a segment named WEB-LS from the NSX UI and noticed the segment is not realized on the KVM Transport node.

What are two possible causes for this issue? (Choose two.)

26. A DevOps user has deployed a Kubernetes Pod in vSphere.

What does the term ClusterIP represent within NSX-T?

27. Which log is used to see a failed NSX-T installation of a VIB package on ESXi transport nodes?

28. When a stateful service is enabled for the first time on a Tier-0 Gateway, what happens on the NSX Edge node?

29. A customer is preparing to deploy VMware Kubernetes on an NSX-T Data Center.

What is the minimum MTU size for the UPLINK profile?

30. Which three services are compatible with VRF Lite? (Choose three.)

31. Which statement describes the VMware Virtual Cloud Network Vision?

32. Which CLI command is used to start the NSX Manager virtual machine in the KVM environment?

33. An NSX administrator is creating a NAT rule on a Tier-0 Gateway configured in active-standby high availability mode.

Which two NAT rule types are supported for this configuration? (Choose two.)

34. Which two BGP configuration parameters can be configured in the VRF Lite gateways? (Choose two.)

35. Which three can an administrator define in a transport node profile? (Choose three.)

36. Which two statements describe the characteristics of an Edge Cluster in NSX-T 3.0 Data Center? (Choose two.)

37. A customer has a network where BGP has been enabled and the BGP neighbor is configured on the Tier-0 Gateway.

A NSX-T Data Center administrator used the get logical-routers command to retrieve this information:

Which two commands must be executed to check BGP neighbor status? (Choose two.)

38. Which tool injects packets and provides various observation points along the packet’s path between two NSX-T managed objects?

39. Which three teaming policy modes are supported by NSX-T Data Center? (Choose three.)

40. Which CLI command does an NSX administrator run on the NSX Manager to generate support bundle logs if the NSX UI is inaccessible?