CCNP Enterprise 300-410 Updated Questions v10.02

1. Refer to the exhibit.

BGP is flapping after the CoPP policy is applied.

What are the two solutions to fix the issue? (Choose two)

Configure BGP in the COPP-CRITICAL-7600 ACL

Configure a higher value for CIR under the default class to allow more packets during peak traffic

Configure a higher value for CIR under the class COPP-CRITICAL-7600

Configure a three-color policer instead of two-color policer under class COPP-CRITICAL-7600

Configure IP CEF to CoPP policy and BGP to work

2. Which component of MPLS VPN is used to extend the IP address so that an engineer is able to identify to which VPN it belongs?

VPNv4 address family

LDP

3. Refer to the exhibit.

The ACL is placed on the inbound GigabitEthernet 0/1 interface of the router. Host 192.168.10.10 cannot SSH to host 192.168.100.1 even though the flow is permitted.

Which action resolves the issue without opening full access to this router?

Temporarily move the permit ip any any line to the beginning of the ACL to see if it the flow works

Run the show access-list FILTER command to view if the SSH entry has any hit statistics associated with it

Move the SSH entry to the beginning of the ACL

Temporarily remove the ACL from the interface to see if the flow works

4. What is an advantage of using BFD?

It detects local link failure at layer 1 and updates routing table

It detects local link failure at layer 3 and updates routing protocols

It has sub-second failure detection for layer 1 and layer 2 problems

It has sub-second failure detection for layer 1 and layer 3 problems

5. Refer to the exhibit.

An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired.

Which command fixes the issue?

R1(config)# ip route 0.0.0.0 0.0.0.0 1.1.1.1 track 1

R1 (config)# ip route 0.0.0 0 0.0.0 0 2.2.2 2

R1 (config)# ip route 0.0.0.0 0.0.0.0 2.2.2.2 10 track 1

R1(config)# ip sla track 1

6. An engineer configured a leak-map command to summarize EIGRP routes and advertise specifically loopback 0 with an IP of 10.1.1.1 255.255.255.252 along with the summary route. After finishing configuration, the customer complained not receiving summary route with specific loopback address.

Which two configurations will fix it? (Choose two)

Configure route-map Leak-Route permit 10 and match access-list 1

Configure access-list 1 permit 10.1.1.1 0.0.0.252

Configure access-list 1 and match under route-map Leak-Route

Configure route-map Leak-Route permit 20

Configure access-list 1 permit 10.1.1.0 0.0.0.3

7. Refer to the exhibit.

A junior engineer updated a branch router configuration. Immediately after the change, the engineer receives calls from the help desk that branch personnel cannot reach any network destinations.

Which configuration restores service and continues to block 10.1.1.100/32?

ip prefix-list 102 seq 15 permit 0.0.0.0/32 le 32

route-map FILTER-IN permit 20

ip prefix-list 102 seq 5 permit 0.0.0.0/32 le 32

route-map FILTER-IN deny 5

8. Refer to the exhibit.

An engineer is trying to get a packet destined for 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2.

What action forwards the packets through 10.1.1.1?

Configure EIGRP to receive 192.168.32.0 route with lower metric

Configure EIGRP to receive 192.168.32.0 route with lower administrative distance

Configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24

Configure EIGRP to receive 192.168.32.0 route with longer prefix than /19

9. Which label operations are performed by a label edge router?

PUSH and PHP

SWAP and POP

SWAP and PUSH

PUSH and POP

10. Refer to the exhibit.

Redistribution is enabled between the routing protocols, and now PC2 PC3, and PC4 cannot reach PC1.

What are the two solutions to fix the problem? (Choose two)

Filter RIP and OSPF routes back into OSPF from EIGRP when redistributing into OSPF in R2

Filter all routes except EIGRP routes when redistributing into OSPF in R3

Filter OSPF routes into RIP from EIGRP when redistributing into RIP in R2

Filter all routes except RIP routes when redistributing into EIGRP in R2

Filter RIP routes back into RIP when redistributing into RIP in R2

CCNP Enterprise 300-410 Updated Questions v10.02

Leave a Reply Cancel reply