CCNP Service Provider 300-515 SVPI Exam Questions – Implementing Cisco Service Provider VPN Services – PassQuestion Free Questions To Test Online

1. Which utility can you use to validate an LSP in an MPLS environment?

uRPF

MPLS LSP ping

logging

RSVP

2. What is the primary function of a VRF on a router?

It enables the router to support multiple separate routing tables, which allows the device to handle overlapping IP addresses.

It enables a router to run BGP and a distance vector routing protocol at the same time, which allows it to serve as a VPN endpoint between remote sites.

It enables a router to configure VLANs locally, which provides segregation between networks.

It enables the router to provide faster switching through the network by using labels to identify the input and output interfaces for neighbor routers.

3. Which two statements describe primary differences between MPLS Layer 2 and Layer 3 VPNs? (Choose two.)

Layer 2 VPNs use IPsec tunneling, but Layer 3 VPNs use L2TPv3 tunneling.

Layer 2 VPNs use AToM, but Layer 3 VPNs use MPLS/BGP.

Layer 2 VPNs use BGP, but Layer 3 VPNs use VPLS.

Layer 2 VPNs use L2TPv3 tunneling, but Layer 3 VPNs use GRE tunneling.

Layer 2 VPNs use IPsec tunneling, but Layer 3 VPNs use pseudowires to provide tunneling.

4. Refer to the exhibit.

A network engineer has been called to configure the four PE devices in order to enable full communication among the four CE devices connected to them. While starting to configure, he experienced a connectivity issue.

Which two tasks should the engineer perform in order to begin the process correctly? (Choose two.)

Configure PE3 to export route-targets 100:1 and 200:2.

Configure PE3 to import route-targets 100:1 and 200:2.

Configure PE4 to import route-targets 101:1 and 202:2.

Configure PE2 to export route-targets 300:3 and 400:4.

Configure PE1 to import route-targets 300:3 and 400:4.

5. Refer to the exhibit.

If the two devices are operating normally, which two conclusions can you draw from this configuration? (Choose two.)

CE1 must use OSPF to establish a neighbor relationship with PE1.

PE1 labels the routes it learns from CE1 with the route-target 222:2 and shares them with its VPNv4 peers.

PE1 labels the routes it learns from CE1 with the route-target 111:1 and shares them with its VPNv4 peers.

The PE-CE routes between the devices are being exchanged by OSPF E. CE1 is supporting CSC.

6. Which two frames can be configured on an Ethernet flow point? (Choose two.)

of a specific VLAN

with different type of service values

with identical type of service value

with different class of service values

with no tags

7. In an Ethernet Virtual Circuit environment, which restriction do bridge domains have when STP is running?

The STP mode must be RSTP or PVST+

Bridge domains must be mapped to a different VLAN.

The STP mode must be MSTP

Bridge domains must belong to different MST instances.

8. Refer to the exhibit.

An engineer is implementing an MPLS P2MP TE solution.

Which type of router can serve as the midpoint router and the tailend router in this P2MP TE network implementation?

headend

source

transit

bud

9. An engineer is investigating an EVPN traffic flow issue.

Which type of traffic should the engineer allow in an EVPN Tree Service in order to fix this issue?

known unicast from a leaf to another leaf

unknown unicast from a leaf to another leaf

multicast from a leaf to another leaf

known unicast from a root to another root

10. An engineer is investigating an MPLS LDP issue.

Which command should an engineer use on a Cisco IOS XE device to display the contents of the LFIB?

show mpls forwarding-table

show mpls ldp neighbors

show mpls ldp labels

show mpls ldp bindings

CCNP Service Provider 300-515 SVPI Exam Questions – Implementing Cisco Service Provider VPN Services

CCNP Service Provider 300-515 SVPI Exam Questions – Implementing Cisco Service Provider VPN Services

Leave a Reply Cancel reply