NS0-183 Real Questions To Pass NetApp Certified Storage Installation Engineer, ONTAP

1. A customer wants to transfer data from an existing Data ONTAP 8.2 7-Mode system to a new AFF A220 ONTAP 9.5 cluster by using 7MTT 3.3.2 copy-based transition. When you try to start the first transition job, you receive an error message that copy-based transition is not possible between those two clusters.
Which action will solve this problem?

2. During an installation of an AFF A400 cluster, you need to configure secure multitenancy.
What will enable you to accomplish this task?

3. What is a benefit of ONTAP System Manager?

4. Click the Exhibit button. Exhibit
You just completed racking an AFF A800 cluster running ONTAP 9.7. You are about to cable the controllers to the network.
Referring to the exhibit, which two ports should be used to connect to the management network? (Choose two.)

5. A host cannot connect to the namespace configured on an NVMe-enabled SVM.
In this scenario, what are two reasons for this problem? (Choose two.)

6. According to NetApp documentation, what should be used when using the Cluster Switch Health Monitor (CSHM) and log collection features?

7. You are installing a new ONTAP 9.7 cluster by using System Manager Guided Setup.
In this scenario, which IP address is optional?

8. You are adding nodes to a 2-node switchless cluster.
Before you add the nodes, which statement is correct?

9. Click the Exhibit button. Exhibit
While you are showing the NetApp Support website, your customer asks you to ensure that the new ONTAP storage array is covered by support before you complete the knowledge transfer procedure.
Referring to the exhibit, which two widgets would you select to accomplish this task? (Choose two.)

10. Click the Exhibit button. Exhibit
You finished installing an ONTAP cluster and must inform the customer of the completion.
As part of this exercise, you will show how to configure the ONTAP cluster using ONTAP System Manager, so that NetApp will receive notifications of any future issues
Referring to the exhibit, which section would you select to allow the customer to receive this information?

11. What is the default shelf ID for disk shelves with IOM12 modules?

12. You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches.

In this scenario.

Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)

13. Before starting a base installation on an AFF A400, you need to find out the default cluster interconnect ports for the AFF A400 controllers.

In this scenario, which three resources would you use to find this information? (Choose three.)

14. You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves.

How do you verify your configuration?

15. You have installed and configured a new AFF C190 cluster with ONTAP 9.7. Your customer wants you to install the latest version of ONTAP.

In this scenario, what are two methods to update ONTAP? (Choose two.)

16. You install a 4-node cluster with an AFF A400 HA pair and a FAS8300 HA pair. After setup, you are asked to review the audit logs on each controller from a Web browser.

In this scenario, which method provides access to the logs from a Web browser?

17. You have an AFF A400 cluster that is running ONTAP 9.7 software. You are asked to set up FlexCache for NFS volumes.

In this scenario, which statement is correct when implementing FlexCache?

18. When you install a new ONTAP 9.7 4-node cluster, which network type is required?

19. While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.

In this scenario, which two statements are true? (Choose two.)

20. Click the Exhibit button.

You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.

For a high availability, which ports should swap Ethernet cables?

21. You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.

Which tool would you use to accomplish this task?

22. Click the Exhibit button.

A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.

Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)

23. What should you do to change the data protocol of a LIF?

24. You are installing a new AFF A400 cluster and need to access the cluster management LIF from a remote subnet with the fully qualified domain name (FQDN) a400.lab.netapp.com.

In this scenario, which two network components must be configured to log in to ONTAP System Manager from the remote subnet? (Choose two.)

25. In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)

26. Click the Exhibit button.

Your ONTAP cluster shows the cluster network errors that are shown in the event log.

What is used by ONTAP software to log the errors that are shown in the exhibit?

27. You are installing a 4-node AFF A400 cluster and are asked to create a custom security message before and after user login.

Which two security features are used to perform this task? (Choose two.)

28. Click the Exhibit button.

As shown in the exhibit, you have an 8-node ONTAP 9.7 cluster. You are asked to set up a SnapMirror volume relationship between node-1 and node-8 in the same cluster.

In this scenario, which two network components are used by the SnapMirror volume? (Choose two.)

29. You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.

In this scenario, which two health outputs would this command show you? (Choose two.)

30. You must replace a FAS2750 switchless cluster with an AFF A220 switchless cluster for a customer. The customer requires that you transfer the data from the FAS2750 cluster to the AFF A220.

In this scenario, which two methods would you use to migrate the customer’s data? (Choose two.)